Ever heard the sad tale of a staggering repair bill from a broken timing belt? Bad news. Let's take a lesson from their woes and remember to think about our timing belt.

First, let's review what a timing belt does. The top part of the engine, over the cylinders is called the cylinder head. The head contains the valves. There's at least one valve that lets the fresh air into the cylinder. This air, mixed with fuel, burns to create power. Then another valve or two open to allow the exhaust out of the engine. Each cylinder has 2 to 4 valves - that's 12 to 24 valves for a V-6, up to 32 values on a V-8. The opening and closing of the valves is done by a camshaft. The timing belt uses the rotation of the engine to drive the camshaft which opens and close the valves. It's called a timing belt because it has to be adjusted to rotate the camshaft to keep proper time with the engine so that everything's in sync.

The timing belt is a toothed rubber belt . But some cars use a timing chain or timing gears instead of a belt. Timing chains and gears are much more durable, but manufacturers are using belts more because they are quieter - and cheaper. If you have a small or mid-sized passenger car, crossover or mini-van, chances are you have a timing belt.

Unfortunately, timing belts fail without any warning. That shuts you down right away. A technician can inspect your timing belt and look for cracks and looseness. But getting to the belt to take a look can be almost as much work as changing it on some cars. That's why manufacturers recommend replacing the belt from time to time. For most vehicles it's from 60,000 to 90,000 miles or 95,000 to a 145,000 kilometers. If your owners' manual doesn't specify an interval ask your service advisor.

One AutoNetTV producer has had two timing belts fail. The first was while he was waiting at a stop light - that repair cost several thousand dollars. The second was while driving on the highway - that one cost more than twice as much. Both had the cars out in the shop for three weeks. His cars had what we call "interference engines", meaning that the valves and pistons are very close to each other. If the timing belt slips even one notch, the pistons will slam into the open valves. That's why our friend's highway failure was so much more expensive - his engine was traveling so fast that the valves were smashed and they chewed up the cylinder head.

A non-interference engine will just shut down if the timing belt breaks. You're stranded, but the engine doesn't suffer permanent damage. In both cases, our hapless friend was just a couple oil changes past the recommended interval for changing the timing belt. This is one of those things that you just cannot put off. Now replacing a timing belt is not cheap - but repairs for a broken belt can be many times as much.

Check your owners' manual right away - especially if you have more than a 60,000 miles or 95,000 kilometers. You may need to get that belt replaced right away. And on many cars, the timing belt drives the water pump. So, it may be a good idea to replace the water pump while you're at it because 90% of the work required for the new pump is already done with the belt change. Doing both at the same time saves you a lot of money because as they say, "timing's everything". Parts, Timing Belt

You would never like to drink a glass of mud, right? Well, your car feels the same way. It needs a steady supply of clean fuel in order to run well and deliver good fuel economy. The fuel filter's job is to clean dirt and rust out of the fuel before it gets to your engine. A clogged fuel filter can actually choke off the engine so that it won't start or run. Some fuel filters have a bypass valve that allows fuel to go around the clogged filter so your car will still run. But, then the contaminated fuel can plug your fuel injectors and allow damaging particles into your engine.

A car with a partially clogged fuel filter might run well around town, but sputter and strain on the highway because it's starving for gas. There are two things that affect how often you need to replace the filter. They are: where you drive and the gas you buy. If you drive a lot on dirt or gravel roads in rural California, your fuel filter will have a harder time keeping the fuel clean.

And, we hate to say it, but buying the cheapest gas from cut-rate Clovis area stations sometimes means dirtier fuel that'll clog the filter sooner. Major brands tend to be cleaner and certainly have higher levels of detergent additives.

Of course, your manufacturer recommends intervals for changing the fuel filter. But, it's a little more complicated than that. Some manufacturers stopped listing recommended intervals for fuel filter replacement or have very long intervals like every five years or eighty thousand miles. So you may need to look to other sources for recommendations. Cars older than six or seven years are especially at risk because they have had time for dirt and rust to build up in the fuel tank. A clean fuel filter keeps the gas flowing. Even a partially clogged filter puts added strain on the fuel pump. That can shorten its life and result in a costly repair.

As is often the case, spending a little money now on something as inexpensive as a fuel filter can save money down the road. At Ball Tire in Fresno, we can check your fuel filter. It is better than fixing a burned out fuel pump or ruined fuel injectors.

So you love our job, and your family life is great: You have achieved balance. But can you the same for your wheels? You can tell if your tires are out of balance by vibrations at higher speeds. If one of the front tires is out, you feel the vibration in the steering wheel. If it's a back tire, you'll feel the vibration in your seat.

Tires and wheels are pretty heavy. When a tire is mounted on a wheel, it is usually not perfectly balanced. So the tire technician will spin the tire on a machine to determine where it's too heavy. He will then place weights on the wheels in strategic locations to balance it out. When a tire is out of balance, it actually bounces down the road instead of rolling smoothly. Since the average size tire rotates at about 850 revolutions per minute at 60 MPH, it is actually slamming into the pavement 14 times a second. That's where you get your vibration.

Most people are surprised at how smoothly their car rides after balancing all four wheels.

Most high-quality tires hold their balance pretty well. They just get out of balance gradually with normal wear and tear. If you suddenly feel a vibration, it is probably because you lost a wheel balancing weight along the way. Definitely get a balance if you feel a vibration, change your rims or have a flat repaired. Putting off a needed balance job leads to excessive tire wear, wear to your shocks, struts, steering and suspension parts. wheel balancing not only improves your ride and handling, but also can save you some big repair bills and possibly an accident. Additionally, you will get better gas mileage.

Some people have their tires balanced at every rotation. Others do it every other time. Check your owners' manual for your requirements, or ask your technician. Doing thus will put you on the path to mechanical wheel balance

.

If you're a quart low in your sedan, there isn't enough motor oil to lubricate your engine properly. The extra friction causes drag that reduces fuel economy while you're driving around the Clovis area.

The same goes for dirty oil; it doesn't reduce friction properly. The result is you get to watch those numbers at your local Clovis gas pump rolling higher and higher.

The transmission also needs the proper amount of clean fluid to do its work. When it's in need of service, the transmission drags your fuel economy down.

So keep it clean and give yourself a fighting chance.

Ball Tire
4741 E Kings Canyon Rd
Fresno, California 93702
559-251-4283